CQRLOG - open discusion

Cannot connect rigs after fresh Mint 21.2 installation

Submitted by NZ0T on

I cannot get my Elecraft K4 or K3 to connect to CQRlog since I did a fesh install of Mint 21.2 yesterday. Everything worked fine on 21.1. I am using a fresh install (of course) CQRlog V2.5.2. I am using an FTDI USB adapter with the K3 and the K4 a USB cable. My hamlib is v4.3.1-1build 2. I am in dialout and when I ran dmesg | grep FTDI it showed the converter connected and attached to ttyUSBx. My K4 does connect fine with CQRlog using IP address as device. I have used sudo modprobe to make sure the FTDI diver is attached properly. Rigctl is correct.

Forums: 

still problem clublog no sending qso

Submitted by ik3ocd on

hello all, sorry I come back again on the clublog question, as advised I modified in etc/host adding the line 5.153.81.176 secure.clublog.org, it seems that it actually works, but looking at the clublog site under my log it seems that it has not been sent no information to my QSO , I state that my password and user are fine , at this point I no longer have an idea of what is happening .
my linux system using ubuntu 23.04 with latest cqrlog v.117 test. flavio ik3ocd

Forums: 

TS 570D HamLib 4.3.1 Response

Submitted by GM4NFI on

Hi

For 2 days I have been trying to reply. I can upload as a new topic but not as a reply.
All seems fine, I enter the text, click to say I am not a robot and then click upload.
Timer appears, no errors but the timer disappears far too fast and my reply is not uploaded.

This is a reply to TS 570D HamLib 4.3.1

Thanks for all the replies. Here is where I have got to.
I still have the original problem but I am at least starting to track the problem down.

my user name is djcleckie on my Linux (Ubuntu 22.04 box)

Forums: 

TS 570D HamLib 4.3.1

Submitted by GM4NFI on

Radio is a TS 570D

Radio is setup for Baud 9600 1 stop bit. The default.
CAT control working OK on a PC running Logger32
To get CAT to work with a PC running Logger32 I need the following settings
8N1, 9600 baud
I also need CTS/RTS handshaking to be set on. Will not work without this set.

On Linux PC running Ubunu 22.04
Installed CQRLog 2.5.2

Initially all seemed fine but I cannot get CAT Control to work.
Hamlib version 4.3.1 is installed.
ls /dev/ttyUSB*
gives
/dev/ttyUSB0

Forums: 

":1" is an invalid integer at downloading from ARRL

Submitted by JE8VZK on

Sorry for not positive question.
I compiled TQSL 2.6.5 from ARRL source to import p12 file.
I succeeded also to import and uploaded unintemtionally carelessly whole log over 35,000 QSOs. Maybe only not yet uploaded, I suppose.

But I tried "download from ARRL, and got a message ":1" is an invalid integer."
I converted the downloaded adif CRLR to LF.
But I could not find invalid that.
Is this caused by the file I uploaded ?

Forums: 

wsjt-x not activated from CQRlog

Submitted by N0NOW on

I have new installs of Ubuntu 22.04, CQRlog 2.5.2 (I think), wsjt-x 2.6.1, MariaDB 10.11.2, and hamlib 4.6. It appears that each of those function on their own, but do not play well together. Specifically, when in CQRlog I click "Remote mode for wsjt," wsjt does not start. The wsjt UDP Server is 127.0.0.1 and the UDP Server port number is 2237, as expected.

What have I forgotten to do?

Thanks for all suggestions.

Joe
N0NOW

Forums: 

CQRlog crash when opening MariaDB

Submitted by N0NOW on

I am running Ubuntu 22.04 and CQRlog 2.5.2, both new installs. When I open CQRlog, the small picture appears as expected, but after a few (10?) seconds, an error popup is displayed. The error is:
Error during connection to database: TMySQL57Connection : Server connect failed.

Then the "Database Problem" window from CQRlog appears, and suggests the FAQ (which did not help) and the urging to send you the final lines of the mysql.err file.

I look forward to your comments.
Thanks,
Joe n0now

Forums: 

Level of address detail

Submitted by w1jt on

Hello all.
This is Jim W1JT from the Eastern MA area. I'm coming from HRD's logbook and I'm in the process of getting accustomed to CQRLOG.

When I'm on HRD's logbook and my QRZ credentials are entered in, when I go to log a contact I'm able to see the name, city, and state. So when I put W1JT into I see my name, Holbrook and MA.

When I do the same on CQRLOG (with my QRZ credentials entered in just like HRD) I get my name but that's about it. It doesn't go to the level of city and state like HRD does.

Forums: 

Pages

Subscribe to RSS - CQRLOG - open discusion