CQRLOG - open discusion

USB port number??

Submitted by f6eeq on

Hi all,

I have difficulty to connect my IC7610, and eventually my Winkeyer to CQR.

I'm with Debian10.

Ports listing gives:

T: Bus=01 Lev=04 Prnt=11 Port=01 Cnt=01 Dev#= 12 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=10c4 ProdID=ea60 Rev= 1.00
S: Manufacturer=Silicon Labs
S: Product=CP2102 USB to UART Bridge Controller
S: SerialNumber=IC-7610 13002399 A

Forums: 

Mint 20 and CQRLOG windows

Submitted by NZ0T on

Since I upgraded to Mint 20 Cinnamon and compiled the latest version of CQRLOG the way the windows act is different. The windows I use are New QSO, DX Cluster, RBN Monitor, TRX Control, and DK0WKY Propagation. In previous versions of Mint when I clicked on the CQRLOG icon in the task bar (when the program was running but minimized) all of the windows would come up. But now when I do that only the NEW QSO window comes up. If I hover over the icon in the task bar I see the other windows but i have to click them one at a time to get them all back full screen. It's a pain in the rear.

Forums: 

ADIF export cannot find thumb drive.

Submitted by NZ0T on

Last week I did a fresh install of Mint 20 Cinnamon and also the latest CQRLOG which I compiled per Saku's tutorial. All worked just fine until I attempted to export my log to a thumb drive. With Mint 19, 18 and 17 every Sunday I would export my entire log to a thumb dive via "QSO list-file-export-ADIF" and then select my thum drive in the "save file as" window and export to the drive. When I tried this yesterday with the new install all was fine until the "save file as" window came up. My thumb drive cannot be found and the actual window is different.

Forums: 

Command Line Arguments

Submitted by N2EHL on

Are there any command-line arguments supported by CQRLog? I can't find any documentation about this.

Specifically, I'd like to launch the application with "Remote for WSJT-X" on, as that how I use it most often.
I'd prefer to turn it off when I'm not using it, rather than having to manually turn it on most times that I launch CQRLog.

Thanks for great logger!

Rich, N2EHL

Forums: 

CQ Monitor window gone

Submitted by NZ0T on

Using Mint 20, WSJT V.2.3.0-rc1. At first when I checked the "remote mode for wsjt" box the CQ monitor showed up small and in the upper left hand corner of my screen. One I enlarged and moved it all was fine. But just now when I tried to enlarge it disappeared and I cannot find it. I have tried restarting with no luck. Remote mode is working fine but the CQ Monitor window is gone and I cannot find it. Does the same thing on JTDX. Any ideas anyone?

73, Bill NZ0T

Forums: 

Errors after export adif file to ClubLog

Submitted by Anonymous (not verified) on

I exported the entire log in adif file to ClubLog with strange errors. DXCC for over 450 qso is shown in ClubLog as "SATELLITE, INTERNET OR REPEATER" which is not true and distorts the dxcc statistics. If I edit these qso manually in cqrlog then they are uploaded to ClubLog correctly. But manual editing of 450 qso is a bit too much ;)
Is it possible to correct these qso's in some way?

Slav, EI6KW

Forums: 

Transfer from N1MM to CQRLog does not work

Submitted by EA3CV on
Hi,
I'm trying to connect N1MM to CQRLog to automatically send QSOs, but I can't get them to show up in CQRLog.
I'm using:
Ubuntu 20.04.1 LTS
Cqrlog Ver: 2.4.0 (001) Date: 2019-10-27
The CQRLog can only make it run with: "dbus-launch --exit-with-session cqrlog"
I have configured N1MM+ like this:

Forums: 

Mint 20 TQSL Installation

Submitted by NZ0T on

Fresh Mint 20 install. I have CQRLOG up and running thanks to a lot of help found searching this forum. Especially Saku's thread about installing fresh and compiling the latest - very helpful. I am having trouble getting TQSL to install. I downloaded TQSL and then right clicked on the open directory. Then tried the procedure I always used with Mint 19.3:

Click on "open in terminal"
Type "cmake ."
Type "make"
Type "sudo make install"

But at cmake . I get the following errors:

Forums: 

Installing CQRLOG with existing MySQL or MariaDB running as service [SOLVED]

Submitted by wd5hhh on

My hamshack computer is a wonder box of many functions. It functions as my personal computer and as a local network server. I have recently upgraded to Ubuntu 20.04.1 from 18.04.x. On the personal side I use Ham radio applications. On the server side I am trying to set up a development/test server for web applications. On 18.04 I had CQRLOG working with MySQL as well as Joomla! working with the same server with the server running as a service. I am having the same issues as others trying to use MySQL and not getting it to work but that is another discussion.

Forums: 

Pages

Subscribe to RSS - CQRLOG - open discusion